Dress on thin straps pattern. Straps for dresses and tops - do it yourself

Model 1.

If you are going to create something by any method, read it, understand the details so that you have an idea of \u200b\u200bthe process. Take, for example, this instruction. See what point K means? This is the depth of cut in the center of the front. Points 3 and 6; this is the depth of the cutout armhole. Compare these values \u200b\u200bwith what you want to have as a result of the simulation. You can change them to either side, i.e. decrease or increase. The same can be said about the width of the entire product in the chest and waist. This is just an example that shows you one of the directions in modeling this kind of blouses or dresses.

If you have not yet built a base pattern for yourself, use our step-by-step instructions and do it.
We take a drawing of our base pattern and copy the shelf and back to a blank sheet of paper

See Fig. 1

To build, we need a separate back and shelf.

Fig. 2

On a back-based pattern on the side cut down from point P, measure 4 cm and put point 1. From point 1, draw a horizontal line until it intersects with the middle line of the back and put point 2. This will be the top cut of the back.

Fig.3

Having departed from the side cut of the base pattern by 1 cm to the left, draw a new line of the side cut parallel to it.

Fig4

Tuck close. The upper and lower sections are drawn in a smooth line.

Fig5

On the pattern of the base of the front, the chest tuck is closed, we transfer it to the tuck at the waist. To do this, cut the line G74 (points G7 and 4 indicate the tops of the tucks of the chest and from the waist).

Fig6

The top of the new tuck (point E) will now be on the bisector of the angle of the opened tuck approximately 4 cm from point G7. To build, you can use the compass.

Fig. 7

On the side cut line down from point P, measure 4 cm and set point 5. Having departed from the side cut by 1 cm, draw a new line parallel to the previous line of the side cut. From point 5, draw a perpendicular to the intersection with the new side cut line and set point 6.
Now draw the upper section of the front of the bodice. On the midway line down from point B4, we lay aside 13-15 cm to get point K. From point G7 upward along the line of a closed tuck, we set aside 10 cm to get point K1. Connecting the points K, K1 and point 6, we draw the line of the upper cut of the front.

Fig. eight

Figure 9 shows the details of the cut of the back and front of the bodice. Adjust the length of the straps during the fitting process on the figure.

And as always, I wish you creative inspiration and self-confidence!

Download in one file | Turbobit | | |

The rights to this article belong exclusively to the author. Full or partial use of the materials in this article in electronic editions of the Internet is possible only if the following conditions are met:
Information about the author should be saved. The heading or at the end of the published reprint should indicate the source www.site Sewing Crafts Internet resource with a direct, active, visible to the user, not closed from indexing by search engines hyperlink to this article.
Reproduction of texts by newspapers, magazines or other replication outside the Internet is possible only with the written consent of the author.

Hardworking - a bright light burns through life, lazy - a dim candle

Straps for dresses and tops - do it yourself

visibility 37882 views

In this article I will tell you how to sew and correctly sew straps on your own. You will also learn how to make adjustable shoulder straps - those that can be lengthened and shortened.

So, let's start with a simple ordinary straps ...

How to sew a shoulder strap.

Firstly, I’ll immediately make a reservation that if it’s not important for you that the straps were made from the same fabric as the dress itself, then straps can be made very quickly from a slanting inlay (sold in fabric departments of stores or in departments of sewing accessories).

The oblique trim looks like a half-finished strap, that is, an even strip of fabric with the edges bent inward (Fig. 3 in the diagram below). So you just save time; no need to cut a long strip, bend and smooth its edges with an iron.

But if this option does not suit you, or you did not find the oblique edging of the size you need, then we will try to make it ourselves. Here's how to do it.

We take a strip of fabric of the required length. The width of the strip should be 4 times wider than the future strap (Fig. 1).

We bend the edges of the strip inward to the middle (Fig. 2, 3) so that the bend is kept flattened with an iron. So we got a slanting inlay. So she looks in the store. In the same edging, you can process the armholes and neck of the dress.

Now, for the edging to become a shoulder strap, it is necessary to fold it again in half, edge to edge (Fig. 4) and stitch it (Fig. 5).

Everything - the strap is ready, you can sew it on the dress. We fix one end of the strap in front, and the other in the back.

How to sew a shoulder strap on a dress.

The first way. You can simply sew stitches tightly. To hide the ends of the straps over the edge of the dress and to sew stronger - such a simple rough way.

The second way. In places of future attachment of the strap to the dress, beautiful decorative rings can be sewn and the strap can be inserted into them and fixed. Here is what I mean:

Now there are many decorative ringlets and buckles strewn with strasses on sale. And the strap with such a little ring will become more elegant.

First you need to sew a piece of shoulder strap in the right place for us (where the strap will be attached to the dress). And attach a ring to this piece (Fig. 1, 2, 3). And then into the sewn-in ring we put the end of our long shoulder strap, bend this end and sew to the shoulder strap (Fig. 4, 5, 6).

And you can buy several ringlets, cut the strap into pieces and connect each ring to each other with a piece of strap (Fig. 7).

The third way - you can sew on the strap (when it is still in the edging stage) so that the edging processed the neck and smoothly turned into a strap. Here is what I mean:

Treat the armholes separately with an oblique (Fig. 2).

And then we take our slanting inlay so long that it is enough to process the neck and make 2 straps. We find the middle on this segment of the oblique inlay and apply this middle to the center of the neck.

And now leading a slanting inlay from the center of the neck, we start it (the neck) with this oblique edging to process first to the left side - the edging goes left along the neck (processes it) reaches the left edge of the neck and there it already turns into a strap (that is, the oblique beige sashes are sewn together with the same stitch that we just neckline scribbled). And the same thing is now on the right side.

Everything, inlay, processing the neck to the right and left of the neck smoothly turned into a strap - Fig. 3.

It can be vice versa - a neckline has been processed with a separate piece of neck, and the neckline used to process the armhole smoothly passes to the strap. It will seem more beautiful to you.

How to handle the edges of the armholes and necks with an edge, shown and described in the diagram below:

The strap is adjustable.

If we want the strap to be shortened or lengthened according to our wishes, we can make an adjustable strap, as in bras.

We need a buckle with a jumper (Fig. 1), a ring (Fig. 2) and a finished strap with a margin of length (Fig. 3).

The end of the strap should be pulled into the buckle so that it simply bends over the jumper and returns to the strap, to which it needs to be sewn after that (Fig. 4, 5, 6).

Now on the back in the place you planned, we attach a piece of strap (Fig. 7), into which we screw the ring (Fig. 8, 9), fasten it well with a few lines (Fig. 10).

Now we put the end of the strap (the one without the buckle) into the ringlet, and we stretch it into the buckle (Fig. 11, 12). The whole strap is ready - we attach this free end that came out of the buckle to the front of the dress. You can simply sew it on, or you can also attach a ring on the front and fasten our end of the strap to this ring.

Now in stores you can buy ready-made adjustable straps - however, their color is limited, and they are usually all narrow. More often they are just black and white, there are transparent ones, and there are also studded with squirrels, with buckles in the form of butterflies or flowers.

A bunch of beautiful ribbons, decorative buckles are also on sale, and from all this variety you can come up with many interesting straplets yourself, which will become an adornment of a simply tailored dress.

It is only necessary to remember a sense of proportion. If your dress already has a decorative element (bow, complicated drapery, elaborately sewed flounces), then the additional decor in the form of decoration on the straps will be superfluous.

That, perhaps, was all I wanted to tell about the straps. All questions, wishes and advice from you, dear readers, I will be glad to see in the comments to the article. You can also place photographs of products sewn by you there.

Good luck with your tailoring!

Everything ingenious is simple! This motto proves once again our beige strap dress. To make a pattern of this dress is very simple, as you will see when you begin to build a dress pattern.

So what is the secret of this charming spaghetti strap dress? It's all about the fabric! Openwork beige fabric with pronounced stripes of patterns solo in this model.

IMPORTANT! The lace that you will use to sew the dress on the straps must be elastic, as there are no tucks on the dress.

Spaghetti Strap Dress: Pattern

The pattern is given in size 46-48.

Before you begin to build a dress pattern on the straps, you need to take measurements:

Chest circumference - 92 cm
waist circumference - 70 cm
Hips - 96 cm
Dress length from the waist - about 56 cm

Fig. 1. Pattern dresses on the straps

Spaghetti Strap Dress: Modeling

Build a pattern of the front and backs of the dress on the straps as shown in the dress pattern.

If your measurements differ from those given above, calculate the required values \u200b\u200busing the above formulas.

IMPORTANT! The dress on the straps is sewn only from elastic materials. The front and back of the dress on the straps are cut in one pattern.

How to make a dress with straps

Spaghetti strap dress with cover.

From elastic lace to cut: front and back of the dress in one pattern with allowances for seams at the side seams - 1cm. Do not make allowances on the bottom of the dress, but arrange the pattern so that scallops go on the bottom of the dress. .

Cut out from elastic lining fabric in tone:front and back of the dress in one pattern with allowances for seams at the side seams - 1 cm. Do not make allowances for the front cut and armholes (!). The allowances at the bottom of the dress are made of lining fabric - 3cm.

For strapless and processing of the neckline and armhole of the dress, you will need a braid about 1 cm wide with scallops on both sides and a length measured (about 80 cm for strapless and about 120 cm for neckline and armhole).

The dress on the straps is sewn on the overlock with an elastic seam.

How to sew a dress on the straps

Sweep and sew the side seams of the dress on the straps. Process allowances.

Sweep and grind the details of the dress from the lining fabric, process allowances, tuck and sew along the bottom.

Fold the cover with the dress on the wrong sides, sweep the front, back and armholes along the cutout and continue to process the dress as a single layer.

To process allowances for the armhole and neckline of the front and back of the dress with an overstitch seam. On the neckline and armholes of the dress, sew a braid.

Measure the required length of braid for strapless. Apply and stitch by tucking the ends of the braid.

To set up printing of pattern No. 217 of A4 format, use “Test square No. 2 ″! The test square is located on the first sheet in the pattern file.

Sundress pattern. Sundress on the straps of a conical A-shaped silhouette, above the knee length. On the front part there are chest tucks, a V-neck. The upper edge of the product is machined. There are cuts in the side seams.

The length of the product in the middle of the backrest is in finished form, see: 38 size: 69.6-72.1, 40 size: 69.6-77.2, 42 size: 69.6-77.2, 44 size: 69, 6-77.2, 46 size: 69.6-77.2, 48 size: 69.6-77.2, 50 size: 69.6-77.2, 52 size: 69.6-77.2, 54 size: 69.6-77.2

General gains, embedded in the pattern: Pg: 2.2 cm., Fri: 32.2 cm., Sat: 12.5 cm.

Recommended Materialfor sewing: for sewing this product, we recommend natural thin fabrics with a dense weave without stretching. Such fabrics will keep their shape well, remove moisture in the heat and dry quickly. Cotton or linen is perfect. Fabrics can be plain or printed.

Fabric consumption with a width of 140 cm: 38 size: 1.0-1.05 m., 40.42 size: 1.05-1.1 m., 44.46 size: 1.25-1.35 m., 48, 50 size: 1.55-1.7 m., 52.54 size: 1.65-1.8 m.

Pattern details are given with machining allowances.

Sewing difficulty - "For Beginners"

The photo shows a sundress sewn in the GRASSER bureau for pattern No. 217

We want to work with Grasser patterns to bring you pleasure, and the sewing process to be understandable, therefore a file with a very detailed description is attached to the pattern, which describes all the stages of work on the product, with step by step PHOTOS OF SEWING TECHNOLOGY!

Also in the description provides detailed information about the required consumption of fabric, materials and accessories.

The pattern in your order will be in two print options:

1. For printing on A4. You need to print the pattern on a regular printer on A4 sheets, then glue the sheets, cut the pattern and you can sew!

2. For printing on a large format plotter. Pattern details are located on a sheet measuring 60 * 172 cm.

March 12/15/2019 02:43:35 AM

Good afternoon. Please tell me, is satin or silk suitable for this model? thanks

Administrator: Hello yes yes will do

Valentine 11/21/2019 16:54:21

Good day. I wanted to download a free pattern, sundress. From the phone.
When you click on the button "Download pattern" opens a bunch of pages with different characters / letters. And that is all. How can I get a free pattern by email?

Administrator: Hello, and on which device do you download the pattern? On the phone? Perhaps you do not have a program for opening zip files.
You need to install the program, or open the pattern on another device where a similar program is installed.

The pattern is downloaded on the site, we do not send patterns to the mail. Try downloading on another device.

89500656117 16.11.2019 17:02:47

Hello, is it possible to sew such a dress from Angora?

Administrator: Hello, our recommendations are that the fabric holds its shape well, without stretching, you can choose the composition at your discretion.

Irina 11/13/2019 00:46:25

Good day! Please tell me, I have Og-84 cm, From - 67 cm, About -90 cm, whether size 42 is right for me or is it better to take 44. Thanks in advance for your reply.

Administrator: Hello, yes, your size is 42. The size of the dress pattern should be chosen according to the chest circumference.

Our table helps to determine the size -

Adel Vilenskiy 08/23/2019 17:39:28

Hello! Please tell me, for height 165, parameters 91/73/102 which size is better? Given that the trapezoid, I tend to 44. But I doubt it

Administrator: Hello, the size of the dress pattern should be chosen according to the chest circumference.
According to your parameters, size 46 is more suitable.

Mila And 07/29/2019 10:18:33

Hello! I sewed this summer dress-sundress. But I just can’t add your photo with the finished product to your site. How to do it?

22.07.2019 13:57:01

Hello!
If you sew a dress on a lining, is it necessary to change the pattern? or the lining and the base layer are cut lonely? lining material silk, the main - silk muslin

Administrator: Good afternoon!
The lining can be tailored to the details of the top.

Elena Muratova 07/17/2019 14:15:19

Good afternoon! I can not decide on the size. My options are 90-75-102.

Administrator: Elena, good afternoon!
Size 46 is suitable for you, with a possible reduction in the chest and an increase in the hips. We recommend that you sew a mock-up or cut out parts with additional allowances before sewing a product from the main fabric, so that you can let out a couple of cm in the fitting.

Marina 07/08/2019 16:00:48

Good morning. Can I use this pattern for sewing the bottom dress?

Administrator: Marina, good afternoon!
Yes, of course, why not. It depends on what material and what will be the top dress :)

Lyuba 06/26/2019 13:28:18

Help determine the size. OG 102, FROM 84, OB 105

Administrator: Hello, size 50 is right for you.

Zulfia 06/25/2019 9:23:26 PM

Tell me, for the size of the chest 97, waist 90cm what size to take?

Administrator: Hello, size 48 is right for you.

Daria Novikova 06/19/2019 20:21:33

Hello, help me decide on the size of the parameters 87-73-99 to take the size 44 or 46? Thank you very much.

Administrator:

Daria Novikova 07/03/2019 20:18:35

Svetlana 06/18/2019 09:55:42

Hello! Tell me, please, can I sew such a sundress on a lining?

Administrator: Hello, you can. We have a pattern without a lining, but you can tailor it yourself.

Olga 06/18/2019 09:54:54

Good afternoon.
I really want to sew this model on my 56p. Please tell me what you need to make an increase?

Administrator: You can add 1 cm for each cut of the side seam (4 cm in circumference), sew the layout and see the fit. Just in case, leave more allowances if there is not enough volume.
You may need to adjust the length of the tuck.
Or it may be necessary to adjust the tuck solution. It all depends on your anatomy, chest fullness. All you need to look at the layout, make changes if necessary and transfer to the pattern.

Svetlana 06/15/2019 18:14:43

Hello! please tell me, what size to take on the parameters 110-97-116, so that it is free to hide the flaws of the figure? Thanks in advance for your reply.

Administrator: Hello, 54 size is right for you.

Hope 06/12/2019 15:24:52

Good afternoon. Tell me whether it is possible to use a tensile doubler when sewing this cotton sundress.?

Olga 06/03/2019 18:51:48

Good afternoon!
Can you please tell me if the blouse fabric of Niagara is suitable for this sundress?

Administrator: Hello, yes, you can sew from Niagara.

Inna 05/27/2019 17:59:17

Hello. OG 82, OT 62. I downloaded 42 size and it’s very big. Which size is better? And is it necessary to glue the share lines if the material is silk? Thank you in advance!

Administrator: Hello, this pattern should not be big for you, the increase in the chest is only 2.2 cm. You can, of course, take the size 40, then in this case you will not have freedom at all in the girth of the chest.

Tell me, was the print on the right scale? The test square when printing was 10 by 10 cm?

Alice 05/22/2019 9:12:51 PM

Hello, I want a sundress of a straight cut and below the knees (to the middle of the calf muscles), will it be appropriate if I choose not my height, but more? or is it better to lengthen on your own?

Administrator: Hello, it’s better to choose your height and add the length of the product.
Breasts that are not your height may not be in place.
Better lengthen.

Anna 05/05/2019 21:22:42

Hello, is a staple suitable?

Administrator: Hello, yes, it does!

Polyansky Natalia14.05.2019 23:59:10

I liked the pattern.
I sewed myself a sundress for study and work from fabric to cage to wear with blouses.
Downstairs made straight and without cuts.
I would like a similar pattern for large sizes.
My mother has long dreamed of a sundress to wear with blouses in the winter and t-shirts in the summer.
Her breast size is 124, waist 117, hips 135.

Administrator: Hello Natalya, thank you very much for the tip! We are glad that I liked the pattern!
Let's think about the large size.

16.04.2019 00:41:19

Good afternoon! Tell me, please, how to narrow the sarafan and make it straight from the trapeze?

Administrator: Hello, you can adjust the side seams, remove how much you need at the bottom and bring out new lines of side seams.

Maria 04/05/2019 21:55:42

Hello. Tell me, by the standards I get 42 size with a growth group of 152-158. But your patterns come with 158 growth. Tell me what size to choose. And will I need to make any adjustments?

Administrator: Hello, you need to determine the size by the circumference of the chest. If your chest circumference is 84, then size 42 is right for you. You need to choose 158-164 height.
You may need to transfer chest tucks, this can be determined by fitting.

Ekaterina Bizyaeva27.03.2019 00:46:22

Good afternoon. I downloaded the pattern, but I can not print it. Test square No. 2 with a real print size comes out 10x10, and the pattern itself then does not fit.

Administrator: Hello, when printing, check the “orientation” setting. In this setting, there should be a "self-portrait / album", because of the incorrectly set orientation, the margins of the sheet may move out.

Try a different scale setting, not "real size", but "custom scale". Set in it the desired percentage, with which the test square will be 10 by 10 cm. Usually it is 100%, but the settings of your printer may vary.

With the same settings with which the test square prints exactly 10 by 10 cm, with a letter and number in the upper left corner and with fields on all 4 sides, you need to print the pattern. Then the pattern will be the right size, with margins and numbering.

If you are printing from a browser, then note that printing from a browser may be incorrect. It’s better to print the pattern by first downloading it to the device.

Detailed instructions for printing patterns are on our website -

Maria 03/20/2019 16:24:03

Hello. On OG 95 what size to take? I do not understand 48 in the table is the Russian size?

Administrator: Hello, yes, we have Russian sizes.
For bust 95 fit 48 size

Diana 03/05/2019 00:04:32

Good afternoon!

I sew a sundress on this pattern. I chose the size in accordance with my measurements (height 156, exhaust gas 74, OT 60, OB 86), that is, size 38 height 158-164.
   After trying on the layout it turned out that the sundress is very large and weighs on me just like on a mannequin in a video on sewing this model.
   The length was below the knee and I reduced it by 10 cm.
   The sundress turned out to be wide, so I stabbed 1.5 cm from the sides. I dropped the armhole by the same amount.
   And then the undercut. Since the front part was bristling with a fold, I did the same manipulations as in the video: I made incisions to the center of the chest and parted them.
What happened can be seen in the attached photos. The undercut became only 7mm.
Question: Do I need to leave a recess? Or does it turn out that with my proportions it is not needed at all?

Administrator: Hello, I consulted with the designer - it is better to leave the chest tuck.

Natalia 02/15/2019 02:33:12

Please tell me, if the fabric with the pattern, is it possible not to make cuts on the sides?

Administrator: Hello, yes, you can!

Evgenia Rudenko 02/06/2019 20:03:35

Hello, tell me, what size is suitable for the parameters Og 101 From 74 About 102?

Administrator: Hello, there is no need to write the same question under different models. The size of the product is selected according to the measurements of your body, and for different models of shoulder products will be the same. Since it is chosen by the circumference of the chest.
Here for waist products it can differ, as it is selected by the circumference of the hips.

For shoulder products (dresses, blouses, coats) Your size is 50.
For belt products (skirts, trousers) your size 48

Evgenia Rudenko 02/19/2019 10:27:50

Good afternoon! Is it possible to use strips of duberlin instead of the adhesive edge, cut off, respectively, along the lobar and oblique?

Administrator: Hello, instead of an edge, you can use doublernine cut along the share. But you need to pay attention to the thickness of doubler; doubler may be thinner than the finished edge.

The oblique edge has a thread stitching, to support the seam and also of course, the thickness of doubler plays a role. In the case of an oblique edge, it is better to use it than doubler.

Elizabeth 02/05/2019 02:22:03

Please tell me, on 86-60-89, what size is better to take so that it does not sit in a wrapping?

Administrator: Hello, size 44 is right for you.

Elizabeth 02/06/2019 19:09:09

And on the model in the photo, what size?

Administrator: Hello, on the model 42 the size and the model itself according to the parameters of 42 size.

Julia 01/31/2019 03:57:29

Hello! Please tell me on 85-64-87, height 154, is it better to take 40 or 42 size?
Thank you in advance:)

Administrator: Hello, size 42 is right for you.

Ruzana 12.22.2018 21:54:37

Good evening. I did not understand a bit, please specify! I take a pattern in size, and I still need + to do this increase ??? Waiting for a reply to the mail! Thanks a lot!

Administrator: Hello, no, the increase is already in the model, nothing needs to be added.

Katya 10/11/2018 00:10:55

Good evening, please tell me on parameters 99-83-104, height 163 what size to choose?

Administrator: Hello, size 50, height 158-164 will suit you

Catherine 10/04/2018 01:30:40

Hello. Tell me, please, I sew this sarafan from faux suede on a knitted basis, a sufficiently dense material, is it necessary to glue the upper sections of the neck, back and armholes? And also a question, I can not find a description of sewing and fabric consumption. Usually in hard copy.

Administrator: Hello, yes, it’s better to glue it.

The description file is located along with the pattern files in the zip archive that you download from the site.
Look for a file with the name: Opisanie_poshiva_sarafan_217_pay.pdf

Tatyana 09/07/2018 02:28:03

Good afternoon! Tell me, please, is it possible to sew this model from silk? thanks

Administrator: Hello, you can!

Julia Lobanova 09/04/2018 20:22:10

Very nice patterns. Sewed their cotton 100% topic on this pattern. Very satisfied!

Administrator: Hello. Thank you very much!! Wear it with pleasure!

[email protected] 15.08.2018 16:49:18

Hello, usually all your patterns on me sit perfectly. I generally have a very standard size 44, even the seamstresses in the studio praised. But this sundress somehow ... hangs out, or something. It seems that he is too big in the area of \u200b\u200bgirth above the chest. It should be?

Administrator: Hello, no, it should not be. Compare the bodice of the sundress with the patterns - you did not stretch the top ?. Slices are oblique and can easily deform.

And all the figures still have features, so sometimes some models require adjustments.

Olga 08/08/2018 16:59:37

Good afternoon. Tell me, please, is leather, suede, artificial leather suitable for this model? I want a winter version of such a sundress. Thanks.

Administrator: Hello, yes, it does.

Olga 08/16/2018 03:48:17

Elena 07/26/2018 11:49:30 a.m.

Hello!
Thank you very much for the pattern and the master class!
The pattern didn’t suit me a bit, I chose the right pattern for my height (158-164), but the tucks are located as if for a higher height. About 2 cm below.

Administrator: Elena, good afternoon!
Thank you for your feedback. We are glad that you appreciated the pattern and the master class!
The location of the tucks may depend on the individual characteristics of the figure, as well as on the length of the straps. Therefore, we always recommend to sew the layout before the main sewing, in order to take into account all the nuances of fitting the product exactly on your figure.

Maria 07/23/2018 11:13:10

Good afternoon. On exhaust gas 92 and OB 104 which size is better to choose?

Administrator: Maria, good afternoon!
We recommend that you buy a pattern of size 46, but when sewing the layout add thigh allowances so that if necessary, release a few centimeters during fitting. Adjusting the pattern on the hips will be easier than on the chest.

Balnur Kubasheva 07/17/2018 15:56:52

Hello. Here in the master classes you used the glue edge, and what if I did not find such glue edges in my city (with and without a thread in the middle). And you have to order, delivery is problematic. And I live in Kazakhstan in Aktau. In our stores only web-braid. Glue, duplicates are in the footage. How to be what can be replaced, tell me. Thank you for being there.

Administrator: Good afternoon! You can make the lobe edge yourself by simply cutting the doubler along the lobar width you need.

Lyudmila 07/12/2018 17:20:26

Hello! And can you cut this sundress obliquely? From a less dense fabric?

Administrator: Good afternoon! The pattern is designed for cut on a fractional, if you cut on a slant, you will have to make adjustments.

Daria Sokova 07/12/2018 17:16:41

Hello! But how to adjust the pattern in the section of the cut, if I want to remove the width along the entire length of the dress?

evgeny 07/07/2018 11:43:19

Hello, pdf on a plotter asks for a password when trying to open it in Photoshop / Korel.
Corrections to make I have no problem, just open and print on the machine.

Administrator: good afternoon! Try to open a pattern in a free program for shading PDF Adobe Reader

Inessa 07/10/2018 16:16:44

Hello, is knitwear suitable for this model?

Malka 07/09/2018 16:42:23

Thank you very much, beloved Grasser for, as always, an excellent pattern! Coincided at times. I wear it with pleasure!

Administrator: Thanks!

Evgeniya 07/09/2018 16:35:31

Hello! I can’t download the pattern. Some kind of code opens ... (

Administrator: Good afternoon! Try downloading the file from another browser on your computer.

Maria Goncharova 07/09/2018 16:18:56

Hello, I printed the pattern - a test square of 10 by 10. But the allowances are weird — there are more seams at the side seams than in other places. Maybe something with the settings? And the edging on the edge of the page is 1.5 cm. It was just that in the previous pattern there was less

Administrator: Good afternoon! That's right, this model has such processing allowances

Oksana 07/07/2018 13:49:06

Please tell me, teenage girl OG 76, FROM 65, and hips 90 ... Height 167. I'm afraid taking 38 size, it will not fit in the hips ...

Administrator: Good afternoon! When choosing the size of the shoulder products, we recommend that you focus on the girth of the chest and, if necessary, adjust the pattern in the hips.
We advise you to choose 38 size and slightly expand the pattern in the hips.

Ksenia 06/29/2018 20:13:48

Hello, tell me, is a fabric with a coupon suitable? I printed the pattern and see that the bottom is not straight.

Administrator: Hello, yes, the bottom is rounded, whether it fits or not, depends on which coupon.